GLES 2 doesn't have GL_MAX_TEXTURE_UNITS. Instead the cogl backend
uses GL_MAX_TEXTURE_IMAGE_UNITS with a maximum limit of 16. The same
restriction is now used in the test.
This adds a simple test for ClutterCairoTexture that draws two
rectangles to the cairo surface in an idle callback and then verifies
that they appeared at the right colours in the paint callback. If that
succeeds then the second time the idle callback is invoked it will
replace one of the rectangles with a sub region update and the
following paint callback will again verify the rectangles.
Instead of asking gtester to run ./test-conformance directly we now tell
it to run a list of wrapper scripts. This results in each test being
spawned in a separate process avoiding leakage of state between tests
which has been a big problem with the conformance tests for quite a
while now.
Otherwise it seems that rounding errors will cause the fragments at
the edge of the quad to blend with neighbouring quarters of the
texture which cause the test to fail.
A few of the tests connected to the paint signal but never
disconnected it. Most of these handlers had a call to g_main_quit in
them which meant that it could sometimes cause subsequent tests to
exit after the first frame is painted. Most of the tests don't
validate any of the results until after a couple of frames have been
rendered so this ended up skipping out the test entirely.
To workaround this the test setup function now disconnects all
handlers for the paint signal on the default stage before the test is
run.
The on_paint function for test-cogl-readpixels tries to temporarily
set the projection, modelview and viewport to its own values. However
it was never restoring the saved values so it could affect the results
of subsequent tests.
This adds a test which creates a material using the maximum number of
layers. All of the layers are assigned a white texture except the last
which is set to red. The default combine mode is used for all of the
layers so the final fragment should end up red.
Currently Cogl doesn't provide a way to query the maximum number of
layers so it just uses glGetIntegerv instead. This might cause
problems on GLES 2 because that adds additional restrictions on the
number of layers.
http://bugzilla.openedhand.com/show_bug.cgi?id=2064
This changes the original tests so that it splits the original path
into two sub paths. When adding a new block to the copied path it also
adds another sub path. This further stresses the path copying
mechanism and exposes a bug.
It also tests intersections by drawing a self-intersecting path and a
path with two sub-paths that overlap. Where the path overlaps it
should be inverted.
This renders a texture using different combinations of wrap modes for
the s and t coordinates and then verifies that the expected wrapping
is acheived. The texture is drawn using rectangles, polygons and
vbos. There is also code to test a rectangle using an atlased texture
(which should test the manual repeating) however the validation for
this is currently disabled because it doesn't work.
http://bugzilla.openedhand.com/show_bug.cgi?id=2063
This tests various paths drawing rectangles and verifies that the
expected pixels are filled in. Some of the paths are drawn by copying
an existing path and modifying it which should test the copy-on-write
code.
The test creates a GL_TEXTURE_RECTANGLE_ARB texture using
cogl_texture_new_from_foreign and confirms that rendering it works
correctly. If the rectangle texture extension isn't available then
this test always succeeds.
http://bugzilla.openedhand.com/show_bug.cgi?id=2015
cogl_read_pixels() no longer asserts that the format passed in is
RGBA_8888 but instead accepts any format. The appropriate GL enums for
the format are passed to glReadPixels so OpenGL should be perform a
conversion if neccessary.
It currently assumes glReadPixels will always give us premultiplied
data. This will usually be correct because the result of the default
blending operations for Cogl ends up with premultiplied data in the
framebuffer. However it is possible for the framebuffer to be in
whatever format depending on what CoglMaterial is used to render to
it. Eventually we may want to add a way for an application to inform
Cogl that the framebuffer is not premultiplied in case it is being
used for some special purpose.
If the requested format is not premultiplied then Cogl will convert
it. The tests have been changed to read the data as premultiplied so
that they won't be affected by the conversion. Picking in Clutter has
been changed to use COGL_PIXEL_FORMAT_RGB_888 because it doesn't need
the alpha component. clutter_stage_read_pixels is left unchanged
because the application can't specify a format for that so it seems to
make most sense to store unpremultiplied values.
http://bugzilla.openedhand.com/show_bug.cgi?id=1959
Allow a ClutterModel to be constructed through the ClutterScript API.
Currently this allows a model to be generated like like this:
{
"id" : "test-model",
"type" : "ClutterListModel",
"columns" : [
[ "text-column", "gchararray" ],
[ "int-column", "gint" ],
[ "actor-column", "ClutterRectangle" ]
]
}
where 'columns' is an array containing arrays of column-name,
column-type pairs.
http://bugzilla.openedhand.com/show_bug.cgi?id=2007
The adds tests for the remaining layer combine functions, the 1 minus
value operator and the TEXTURE_N source. Note however that Cogl
currently fails when parsing a TEXTURE_N source so the test is
commented out.
We need to make the Stage set the MAPPED flag on itself if we want to
verify the MAPPED state. That was always the case - it just worked
before because the Stage was shown at least once.
Since all conformance tests share the same state we should not touch
stuff like the stage size; sharing is already fairly complex and adds a
lot of caveats on the implementation of a conformance test unit, and if
we make tests influence later ones then we might slip in bugs or false
negatives - thus defeating the whole point of a conformance test suite.
The g_assert_cmpint() macro prints out not just the assertion condition
but also the assertion contents; this is useful to catch wrong values
without incrementing the verbosity of the test itself.
Since the "internal" state is global, it will leak onto actors that you
didn't intend for it to, because it applies not just to the actors you
create, but also to any actors *they* create. Eg, if you have a dialog
box class, you might push/pop_internal around creating its buttons, so
that those buttons get marked as internal to the dialog box. But
ctx->internal_child will still be set during the *button*'s constructor
as well, and so, eg, the label and icon inside the button actor will
*also* be marked as internal children, even if that isn't what the
button class wanted.
The least intrusive change at this point is to make push_internal() and
pop_internal() two methods of the Actor class, and take a ClutterActor
pointer as the argument - thus moving the locality of the internal_child
counter to the Actor itself.
http://bugzilla.openedhand.com/show_bug.cgi?id=1990
When creating a Cogl sub-texture, if the full texture is also a sub
texture it will now just offset the x and y and reference the full
texture instead. This avoids one level of indirection when rendering
the texture which reduces the chances of getting rounding errors in
the calculations.
The test was calling g_object_get to fetch the "opacity-start" property
(unsigned int) into a guint8 local variable. It's a bit of a mean trap
given that the getter function returns guint8 values so this also adds a
comment explaining what's going on.
The whole point of having the Animator class is that the developer can
describe a complex animation using ClutterScript. Hence, ClutterAnimator
should hook into the Script machinery and parse a specific description
format for its keys.
This adds three new texture backends.
- CoglTexture2D: This is a trimmed down version of CoglTexture2DSliced
which only supports a single texture and only works with the
GL_TEXTURE_2D target. The code is a lot simpler so it has a less
overheads than dealing with slices. Cogl will use this wherever
possible.
- CoglSubTexture: This is used to get a CoglHandle to represent a
subregion of another texture. The texture can be used as if it was a
standalone texture but it does not need to copy the resources.
- CoglAtlasTexture: This collects RGB and RGBA textures into a single
GL texture with the aim of reducing texture state changes and
increasing batching. The backend will try to manage the atlas and
may move the textures around to close gaps in the texture. By
default all textures will be placed in the atlas.
The coverage of the Behaviour sub-classes is currently abysmal. An
initial test suite for Behaviours should at least verify that the
accessors and the constructors are doing the right thing.
This initial test suite just verifies the BehaviourOpacity sub-class,
but it already bumps up the overall coverage by 2%.
It's very useful to see the actual number the reference value is
compared too when the test fails. GTest has g_assert_cmp$type()
functions for that, so make good use of them.
Otherwise the paint handler will still be run for the subsequent
tests. This ends up writing to the ‘state’ variable which used to be
on the stack so it will end up corrupting some stack variable. This
was causing test-cogl-premult to fail.
The sub texture backend doesn't work well as a completely general
texture backend because for example when rendering with cogl_polygon
it needs to be able to tranform arbitrary texture coordinates without
reference to the other coordintes. This can't be done when the texture
coordinates are a multiple of one because sometimes the coordinate
should represent the left or top edge and sometimes it should
represent the bottom or top edge. For example if the s coordinates are
0 and 1 then 1 represents the right edge but if they are 1 and 2 then
1 represents the left edge.
Instead the sub-textures are now documented not to support coordinates
outside the range [0,1]. The coordinates for the sub-region are now
represented as integers as this helps avoid rounding issues. The
region can no longer be a super-region of the texture as this
simplifies the code quite a lot.
There are two new texture virtual functions:
transform_quad_coords_to_gl - This transforms two pairs of coordinates
representing a quad. It will return FALSE if the coordinates can
not be transformed. The sub texture backend uses this to detect
coordinates that require repeating which causes cogl-primitives
to use manual repeating.
ensure_non_quad_rendering - This is used in cogl_polygon and
cogl_vertex_buffer to inform the texture backend that
transform_quad_to_gl is going to be used. The atlas backend
migrates the texture out of the atlas when it hits this.
This adds a test which renders a texture into a 1x1 pixel quad with
and without filters that use mipmaps. The pixel without mipmaps will
be one of the colors from the texture and the one with will be the
average of all the pixels in the texture.
If a user supplied multiple groups of texture coordinates with
cogl_rectangle_with_multitexture_coords() then we would repeatedly log only
the first group in the journal. This fixes that bug and adds a conformance
test to verify the fix.
Thanks to Gord Allott for reporting this bug.
This tests creating a sub texture from a larger texture using various
different texture coordinates. It also tries to read back the texture
data using cogl_texture_get_data.
cogl_push_draw_buffer, cogl_set_draw_buffer and cogl_pop_draw_buffer are now
deprecated and new code should use the new cogl_framebuffer_* API instead.
Code that previously did:
cogl_push_draw_buffer ();
cogl_set_draw_buffer (COGL_OFFSCREEN_BUFFER, buffer);
/* draw */
cogl_pop_draw_buffer ();
should now be re-written as:
cogl_push_framebuffer (buffer);
/* draw */
cogl_pop_framebuffer ();
As can be seen from the example above the rename has been used as an
opportunity to remove the redundant target argument from
cogl_set_draw_buffer; it now only takes one call to redirect to an offscreen
buffer, and finally the term framebuffer may be a bit more familiar to
anyone coming from an OpenGL background.
cogl_clip_push, and cogl_clip_push_window_rect which are now deprecated were
used in various places internally so this just switches to using the
replacement functions.
The ClutterScript parser needs to be extended to parse child properties
and apply them after an actor has been added to a container. In order to
distinguish child properties from regular GObject properties we can use
the "child::" prefix, e.g.:
{
"type" : "ClutterRectangle",
"id" : "child-01",
"child::has-focus" : true,
...
}
Parsing child properties can be deferred to the ClutterScriptable
interface, just like regular properties.
All the ClutterColor parsing rules should be coalesced inside
clutter_script_parse_color(): object, array and string notations
are the canonical ways of defining a ClutterColor inside a
ClutterScript definition. Having a single function in charge of
the parsing cleans up the code.
ClutterScript is a very complicated piece of machinery, with a
parser that has custom variations on top of the basic JSON
format; it could also be extended in the future, so if we don't
want to introduce regressions or break existing ClutterScript
definitions, we'd better have a conformance test suite.
The units under the conformance test suite should be able to use
external files. Linking the files in tests/conform like the
interactive tests do seems like a hack piled on top of a hack, so
instead we should provide a programmatic way for a conformance
test unit to get the full path of a file, regardless of where the
tests/data directory is.
We can use a define to get the full path of tests/data and then
a function using g_build_filename() to construct the path to the
file we want.
Since offscreen rendering is internally forced to be upside down Cogl
needs to reverse the glFrontFace winding order so as not to interfere
with the use of cogl_set_backface_culling_enabled()
This ensures we test that mechanism.
Mostly this was written to verify that we don't flip the data read back from
an offscreen draw buffer. (since all offscreen rendering is done upside
down)
This adds a basic test to check that rendering a few colored rectangles
offscreen works and that the modelview gets restored when switching back to
the previous buffer.
Unlike OpenGL Cogl puts the origin of windows/viewports at the top left
instead of bottom left. This test verifies that we correctly translate Cogl
viewports to OpenGL viewports for the awkward cases where the given viewport
has an offset and/or the viewport has a different size to the current draw
buffer.
It helps to be able to quickly glance at the definition to see which
quadrant of the test actor should be which color, so when debugging a
problem and looking at the visual output you can easily verify if it's being
flipped upside down/left to right.
This contains four tests :-
- A regular onscreen source with a clone next to it
- An offscreen source with a clone. This is currently commented out
because it no longer works.
- An onscreen source with a rectangular clip and a clone.
- An onscreen source with a clip from a path and a clone.
The sources are all a 2x2 grid of colors. Each clone is tested that it
either contains the color that should be at that grid position or that
the stage color is showing through if the source is clipped.
The additional check draws another front facing rectangle but this time with
the texture coords flipped on the x axis. The code that handles sliced
textures in cogl-primitives.c makes some suspicious changes to the geometry
when the texture coords are inverted.
As part of an incremental process to have Cogl be a standalone project we
want to re-consider how we organise the Cogl source code.
Currently this is the structure I'm aiming for:
cogl/
cogl/
<put common source here>
winsys/
cogl-glx.c
cogl-wgl.c
driver/
gl/
gles/
os/ ?
utils/
cogl-fixed
cogl-matrix-stack?
cogl-journal?
cogl-primitives?
pango/
The new winsys component is a starting point for migrating window system
code (i.e. x11,glx,wgl,osx,egl etc) from Clutter to Cogl.
The utils/ and pango/ directories aren't added by this commit, but they are
noted because I plan to add them soon.
Overview of the planned structure:
* The winsys/ API is the API that binds OpenGL to a specific window system,
be that X11 or win32 etc. Example are glx, wgl and egl. Much of the logic
under clutter/{glx,osx,win32 etc} should migrate here.
* Note there is also the idea of a winsys-base that may represent a window
system for which there are multiple winsys APIs. An example of this is
x11, since glx and egl may both be used with x11. (currently only Clutter
has the idea of a winsys-base)
* The driver/ represents a specific varient of OpenGL. Currently we have "gl"
representing OpenGL 1.4-2.1 (mostly fixed function) and "gles" representing
GLES 1.1 (fixed funciton) and 2.0 (fully shader based)
* Everything under cogl/ should fundamentally be supporting access to the
GPU. Essentially Cogl's most basic requirement is to provide a nice GPU
Graphics API and drawing a line between this and the utility functionality
we add to support Clutter should help keep this lean and maintainable.
* Code under utils/ as suggested builds on cogl/ adding more convenient
APIs or mechanism to optimize special cases. Broadly speaking you can
compare cogl/ to OpenGL and utils/ to GLU.
* clutter/pango will be moved to clutter/cogl/pango
How some of the internal configure.ac/pkg-config terminology has changed:
backendextra -> CLUTTER_WINSYS_BASE # e.g. "x11"
backendextralib -> CLUTTER_WINSYS_BASE_LIB # e.g. "x11/libclutter-x11.la"
clutterbackend -> {CLUTTER,COGL}_WINSYS # e.g. "glx"
CLUTTER_FLAVOUR -> {CLUTTER,COGL}_WINSYS
clutterbackendlib -> CLUTTER_WINSYS_LIB
CLUTTER_COGL -> COGL_DRIVER # e.g. "gl"
Note: The CLUTTER_FLAVOUR and CLUTTER_COGL defines are kept for apps
As the first thing to take advantage of the new winsys component in Cogl;
cogl_get_proc_address() has been moved from cogl/{gl,gles}/cogl.c into
cogl/common/cogl.c and this common implementation first trys
_cogl_winsys_get_proc_address() but if that fails then it falls back to
gmodule.
When computing the pixels value of a ClutterUnits value we should
be caching the value to avoid recomputing for every call of
clutter_units_to_pixels(). We already have a flag telling us to
return the cached value, but we miss the mechanism to evict the
cache whenever the Backend settings affecting the conversion, that
is default font and resolution, change.
In order to implement the eviction we can use a "serial"; the
Backend will have an internal serial field which we retrieve and
put inside the ClutterUnits structure (we split one of the two
64 bit padding fields into two 32 bit fields to maintain ABI); every
time we call clutter_units_to_pixels() we compare the units serial
with that of the Backend; if they match and pixels_set is set to
TRUE then we just return the stored pixels value. If the serials
do not match then we unset the pixels_set flag and recompute the
pixels value.
We can verify this by adding a simple test unit checking that
by changing the resolution of ClutterBackend we get different
pixel values for 1 em.
http://bugzilla.openedhand.com/show_bug.cgi?id=1843
Current parsing of units has a number of shortcomings:
* a number followed by trailing space (without any unit specified) was
not recognized,
* "5 emeralds" was parsed as 5em,
* the way we parse the digits after the separator makes us lose
precision for no good reason (5.0 is parsed as 5.00010014...f which
makes g_assert_cmpfloat() fail)
Let's define a stricter grammar we can recognize and try to do so. The
description is in EBNF form, removing the optional <> which is a pain
when having to write DocBook, and using '' for the terminal symbols.
Last step, add more ClutterUnits unit test to get a better coverage of
the grammar we want to parse.
Reviewed-by: Emmanuele Bassi <ebassi@linux.intel.com>
Parse #rgb and #rrggbb in addition to forms with the alpha channel
specified. This allows conversion of colour strings from documents such as
CSS where the alpha channel is not specified when using '#' notation.
This patch also adds the relevant conformance test.
This unit verifies that an Actor class will invoke the get_preferred_*
virtual functions unless the caching is in effect; it also verifies
that the cached values are correctly evicted.
The size requisition and allocation mechanisms should be thoroughly
tested to avoid unwanted regressions.
For starters, we can test the explicit size setting and the side
effects of calling clutter_actor_set_size().
We need to test that the depth sorting of ClutterGroup works correctly
in case we wish to change the data structure that stores the children,
and do so without changing the default behaviour.
We should follow the convention for boxed types initializers of:
<type_name>_from_<another_type> (boxed, value)
For ClutterUnits as well; so:
clutter_units_pixels -> clutter_units_from_pixels
clutter_units_em -> clutter_units_from_em
...
We should still keep the short-hand version as a macro, though.
The ClutterColor conformance test should have a unit for verifying
the RGB<->HLS conversion code, especially the ability to roundtrip
between the two colorspaces.
Fixes and adds a unit test for creating and drawing using materials with
COGL_INVALID_HANDLE texture layers.
This may be valid if for example the user has set a texture combine string
that only references a constant color.
_cogl_material_flush_layers_gl_state will bind the fallback texture for any
COGL_INVALID_HANDLE layer, later though we could explicitly check when the
current blend mode does't actually reference a texture source in which case
binding the fallback texture is redundant.
This tests drawing using cogl_rectangle, cogl_polygon and
cogl_vertex_buffer_draw.
To allow for flushing of batched geometry within Cogl we can't support users
directly calling glReadPixels. glReadPixels is also awkward, not least
because it returns upside down image data.
All the unit tests have been swithed over and clutter_stage_read_pixels now
sits on top of this too.
In order to be ready for the next major version of GLib we need to
disable single header inclusion by using the G_DISABLE_SINGLE_INCLUDES
define in the build process.
Merge branch 'premultiplication'
[cogl-texture docs] Improves the documentation of the internal_format args
[test-premult] Adds a unit test for texture upload premultiplication semantics
[fog] Document that fogging only works with opaque or unmultipled colors
[test-blend-strings] Explicitly request RGBA_888 tex format for test textures
[premultiplication] Be more conservative with what data gets premultiplied
[bitmap] Fixes _cogl_bitmap_fallback_unpremult
[cogl-bitmap] Fix minor copy and paste error in _cogl_bitmap_fallback_premult
Avoid unnecesary unpremultiplication when saving to local data
Don't unpremultiply Cairo data
Default to a blend function that expects premultiplied colors
Implement premultiplication for CoglBitmap
Use correct texture format for pixmap textures and FBO's
Add cogl_color_premultiply()
cogl_texture_new_from_data lets you specify a source format for the users given
data, and an internal format which the user wants the GPU to see. This unit
test verifies that the users data is premultiplied, un-premultiplied or
left alone for a number of (source format, internal format) pairs.
cogl_texture_set_region allows specifying a source format, and the internal
format is determined from the texture being updated. As above we test
a number of format pairs and check Cogl is converting data correctly.
The test verifies that if the user allows COGL_FORMAT_ANY for the
internal_format then by default Cogl will choose a premultipled format for
RGBA textures.
Note: Currently this only tests cogl_texture_new_from_data and
cogl_texture_set_region, we should also test cogl_texture_new_from_file,
cogl_texture_new_from_bitmap and cogl_texture_new_from_foreign.
This test assumes that the textures will be stored internally with exactly
the color given so that specific texture combining arithmetic can be
tested. Using COGL_PIXEL_FORMAT_ANY allows Cogl to internally premultiply
the textures, so we have to explicitly request an unmultiplied format.
The changes in the master clock and the repaint cycle have been
changed, and broke the way the test for the Text actor cache of
PangoLayouts forces a redraw.
We have to call clutter_actor_paint() on the Stage embedding the
Text actor we want to test; this is kinda fugly because if the
Layout has changed it will end up causing a reallocation cycle
in the middle of the Text actor paint. Since it's a test case,
and since forcing redraws is a bit of a hack as well, we can
close both our eyes on that.
This reverts commit 9c5663d671.
The patch was causing problems for applications that expect the
elapsed_time to be at either end of the timeline when the completed
signal is fired. For example test-behave swaps the direction of the
timeline in the completed handler but if the time has overflowed the
end then the timeline would only take a short time to get back the
beginning. This caused the animation to just vibrate around the
beginning.
The new-frame signal of a timeline was previously guaranteed to be
emitted with the elapsed_time set to the end before it emits the
completed signal. This doesn't necessarily make sense for looping
timelines because it would cause the elapsed time to be clamped to a
slightly off value whenever the timeline restarts. This patch makes it
perform the wrap around before emitting the new-frame signal so that
the elapsed time always corresponds to the time elapsed since the
timeline was started.
Additionally it no longer fudges the msecs_delta property to make the
marker check work so clutter_timeline_get_delta will always return the
wall clock time since the last frame.
The master clock now works fine whether or not there are any stages,
so in the timeline conformance tests don't need to set up their
own times.
Set CLUTTER_VBLANK=none for the conformance tests, which in addition
to removing an test-environment dependency, will result in the ticking
for timeline tests being throttled to the default frame rate.
http://bugzilla.openedhand.com/show_bug.cgi?id=1637
Signed-off-by: Emmanuele Bassi <ebassi@linux.intel.com>
Instead of calculating a delta in the master clock, and passing that
into each timeline, make each timeline individually responsible for
remembering the last time and computing the delta.
This:
- Fixes a problem where we could spin infinitely processing
timeline-only frames with < 1msec differences.
- Makes timelines consistently start timing on the first frame;
instead of doing different things for the first started timeline
and other timelines.
- Improves accuracy of elapsed time computations by avoiding
accumulating microsecond => millisecond truncation errors.
http://bugzilla.openedhand.com/show_bug.cgi?id=1637
Signed-off-by: Emmanuele Bassi <ebassi@linux.intel.com>
The test was quiting after the 2nd frame but it should be the third frame because
the test doesn't actually check results until the third frame due to the workaround
for drivers with broken glReadPixels.
(When first written the test would have been verified with the
clutter_main_quit() commented out which gives visual feedback of what the
test does, so the off by one would have snuck in just before uncommenting
and pushing.)
The texture filters are now a property of the material layer rather
than the texture object. Whenever a texture is painted with a material
it sets the filters on all of the GL textures in the Cogl texture. The
filter is cached so that it won't be changed unnecessarily.
The automatic mipmap generation has changed so that the mipmaps are
only generated when the texture is painted instead of every time the
data changes. Changing the texture sets a flag to mark that the
mipmaps are dirty. This works better if the FBO extension is available
because we can use glGenerateMipmap. If the extension is not available
it will temporarily enable automatic mipmap generation and reupload
the first pixel of each slice. This requires tracking the data for the
first pixel.
The COGL_TEXTURE_AUTO_MIPMAP flag has been replaced with
COGL_TEXTURE_NO_AUTO_MIPMAP so that it will default to
auto-mipmapping. The mipmap generation is now effectively free if you
are not using a mipmap filter mode so you would only want to disable
it if you had some special reason to generate your own mipmaps.
ClutterTexture no longer has to store its own copy of the filter
mode. Instead it stores it in the material and the property is
directly set and read from that. This fixes problems with the filters
getting out of sync when a cogl handle is set on the texture
directly. It also avoids the mess of having to rerealize the texture
if the filter quality changes to HIGH because Cogl will take of
generating the mipmaps if needed.
Units as they have been implemented since Clutter 0.4 have always been
misdefined as "logical distance unit", while they were just pixels with
fractionary bits.
Units should be reworked to be opaque structures to hold a value and
its unit type, that can be then converted into pixels when Clutter needs
to paint or compute size requisitions and perform allocations.
The previous API should be completely removed to avoid collisions, and
a new type:
ClutterUnits
should be added; the ability to install GObject properties using
ClutterUnits should be maintained.
Timelines no longer work in terms of a frame rate and a number of
frames but instead just have a duration in milliseconds. This better
matches the working of the master clock where if any timelines are
running it will redraw as fast as possible rather than limiting to the
lowest rated timeline.
Most applications will just create animations and expect them to
finish in a certain amount of time without caring about how many
frames are drawn. If a frame is going to be drawn it might as well
update all of the animations to some fraction of the total animation
rather than rounding to the nearest whole frame.
The 'frame_num' parameter of the new-frame signal is now 'msecs' which
is a number of milliseconds progressed along the
timeline. Applications should use clutter_timeline_get_progress
instead of the frame number.
Markers can now only be attached at a time value. The position is
stored in milliseconds rather than at a frame number.
test-timeline-smoothness and test-timeline-dup-frames have been
removed because they no longer make sense.
All the underlying implementation and the public entry points have
been switched to floats; the only missing bits are the Actor properties
that deal with positioning and sizing.
This usually means a major pain when dealing with GValues and varargs
functions. While GValue will warn you when dealing with the wrong
conversions, varags will simply die an horrible (and hard to debug)
death via segfault. Nothing much to do here, except warn people in the
release notes and hope for the best.
cogl_enable_depth_test and cogl_enable_backface_culling have been renamed
and now have corresponding getters, the new functions are:
cogl_set_depth_test_enabled
cogl_get_depth_test_enabled
cogl_set_backface_culling_enabled
cogl_get_backface_culling_enabled
Setting up layer combine functions and blend modes is very awkward to do
programatically. This adds a parser for string based descriptions which are
more consise and readable.
E.g. a material layer combine function could now be given as:
"RGBA = ADD (TEXTURE[A], PREVIOUS[RGB])"
or
"RGB = REPLACE (PREVIOUS)"
"A = MODULATE (PREVIOUS, TEXTURE)"
The simple syntax and grammar are only designed to expose standard fixed
function hardware, more advanced combining must be done with shaders.
This includes standalone documentation of blend strings covering the aspects
that are common to blending and texture combining, and adds documentation
with examples specific to the new cogl_material_set_blend() and
cogl_material_layer_set_combine() functions.
Note: The hope is to remove the now redundant bits of the material API
before 1.0
The CoglTexture constructors expose the "max-waste" argument for
controlling the maximum amount of wasted areas for slicing or,
if set to -1, disables slicing.
Slicing is really relevant only for large images that are never
repeated, so it's a useful feature only in controlled use cases.
Specifying the amount of wasted area is, on the other hand, just
a way to mess up this feature; 99% the times, you either pull this
number out of thin air, hoping it's right, or you try to do the
right thing and you choose the wrong number anyway.
Instead, we can use the CoglTextureFlags to control whether the
texture should not be sliced (useful for Clutter-GST and for the
texture-from-pixmap actors) and provide a reasonable value for
enabling the slicing ourself. At some point, we might even
provide a way to change the default at compile time or at run time,
for particular platforms.
Since max_waste is gone, the :tile-waste property of ClutterTexture
becomes read-only, and it proxies the cogl_texture_get_max_waste()
function.
Inside Clutter, the only cases where the max_waste argument was
not set to -1 are in the Pango glyph cache (which is a POT texture
anyway) and inside the test cases where we want to force slicing;
for the latter we can create larger textures that will be bigger than
the threshold we set.
Signed-off-by: Emmanuele Bassi <ebassi@linux.intel.com>
Signed-off-by: Robert Bragg <robert@linux.intel.com>
Signed-off-by: Neil Roberts <neil@linux.intel.com>
With the recent change to internal floating point values, ClutterUnit
has become a redundant type, defined to be a float. All integer entry
points are being internally converted to floating point values to be
passed to the GL pipeline with the least amount of conversion.
ClutterUnit is thus exposed as just a "pixel with fractionary bits",
and not -- as users might think -- as generic, resolution and device
independent units. not that it was the case, but a definitive amount
of people was convinced it did provide this "feature", and was flummoxed
about the mere existence of this type.
So, having ClutterUnit exposed in the public API doubles the entry
points and has the following disadvantages:
- we have to maintain twice the amount of entry points in ClutterActor
- we still do an integer-to-float implicit conversion
- we introduce a weird impedance between pixels and "pixels with
fractionary bits"
- language bindings will have to choose what to bind, and resort
to manually overriding the API
+ *except* for language bindings based on GObject-Introspection, as
they cannot do manual overrides, thus will replicate the entire
set of entry points
For these reason, we should coalesces every Actor entry point for
pixels and for ClutterUnit into a single entry point taking a float,
like:
void clutter_actor_set_x (ClutterActor *self,
gfloat x);
void clutter_actor_get_size (ClutterActor *self,
gfloat *width,
gfloat *height);
gfloat clutter_actor_get_height (ClutterActor *self);
etc.
The issues I have identified are:
- we'll have a two cases of compiler warnings:
- printf() format of the return values from %d to %f
- clutter_actor_get_size() taking floats instead of unsigned ints
- we'll have a problem with varargs when passing an integer instead
of a floating point value, except on 64bit platforms where the
size of a float is the same as the size of an int
To be clear: the *intent* of the API should not change -- we still use
pixels everywhere -- but:
- we remove ambiguity in the API with regard to pixels and units
- we remove entry points we get to maintain for the whole 1.0
version of the API
- we make things simpler to bind for both manual language bindings
and automatic (gobject-introspection based) ones
- we have the simplest API possible while still exposing the
capabilities of the underlying GL implementation
The units in the Timeline test suite just rely on the timeline
being a timeout automatically advanced by the main loop. This
is not the case anymore, since the merge of the master-clock.
To make the test units work again we need to "emulate" the master
clock without effectively having a stage to redraw; we do this
by creating a frame source and manually advancing the timelines
we create for test purposes, using the advance_msecs() "protected"
method.
Setting the wrap mode on the PangoLayout seems to have disappeared
during the text-actor-layout-height branch merge so this brings it
back. The test for this in test-text-cache no longer needs to be
disabled.
We also shouldn't set the width on the layout if there is no wrapping
or ellipsizing because otherwise it implicitly enables wrapping. This
only matters if the actor gets allocated smaller than its natural
size.
Bug 1138 - No trackable "mapped" state
* Add a VISIBLE flag tracking application programmer's
expected showing-state for the actor, allowing us to
always ensure we keep what the app wants while tracking
internal implementation state separately.
* Make MAPPED reflect whether the actor will be painted;
add notification on a ClutterActor::mapped property.
Keep MAPPED state updated as the actor is shown,
ancestors are shown, actor is reparented, etc.
* Require a stage and realized parents to realize; this means
at realization time the correct window system and GL resources
are known. But unparented actors can no longer be realized.
* Allow children to be unrealized even if parent is realized.
Otherwise in effect either all actors or no actors are realized,
i.e. it becomes a stage-global flag.
* Allow clutter_actor_realize() to "fail" if not inside a toplevel
* Rework clutter_actor_unrealize() so internally we have
a flavor that does not mess with visibility flag
* Add _clutter_actor_rerealize() to encapsulate a somewhat
tricky operation we were doing in a couple of places
* Do not realize/unrealize children in ClutterGroup,
ClutterActor already does it
* Do not realize impl by hand in clutter_stage_show(),
since showing impl already does that
* Do not unrealize in various dispose() methods, since
ClutterActor dispose implementation already does it
and chaining up is mandatory
* ClutterTexture uses COGL while unrealizable (before it's
added to a stage). Previously this breakage was affecting
ClutterActor because we had to allow realize outside
a stage. Move the breakage to ClutterTexture, by making
ClutterTexture just use COGL while not realized.
* Unrealize before we set parent to NULL in clutter_actor_unparent().
This means unrealize() implementations can get to the stage.
Because actors need the stage in order to detach from stage.
* Update clutter-actor-invariants.txt to reflect latest changes
* Remove explicit hide/unrealize from ClutterActor::dispose since
unparent already forces those
Instead just assert that unparent() occurred and did the right thing.
* Check whether parent implements unrealize before chaining up
Needed because ClutterGroup no longer has to implement unrealize.
* Perform unrealize in the default handler for the signal.
This allows non-containers that have children to work properly,
and allows containers to override how it's done.
* Add map/unmap virtual methods and set MAPPED flag on self and
children in there. This allows subclasses to hook map/unmap.
These are not signals, because notify::mapped is better for
anything it's legitimate for a non-subclass to do.
Signed-off-by: Emmanuele Bassi <ebassi@linux.intel.com>
Bug 1513 - Allow passing in ClutterPickMode to
clutter_stage_get_actor_at_pos()
At the moment, clutter_stage_get_actor_at_pos() uses CLUTTER_PICK_ALL
internally to find an actor. It would be useful to allow passing in
ClutterPickMode to clutter_stage_get_actor_at_pos(), so that the caller
can specify CLUTTER_PICK_REACTIVE as a criteria.
Three tests are now performed on the picked squares. First there is no
covering actor which is the same as the original test. Then there is a
hidden covering actor which should not affect the results. Finally
there is a covering actor with a clip set on it so that only actors
at the borders of the stage should be pickable.
The wrap mode sub-test inside the ClutterText layout cache test
unit has been broken by the recent changes inside the Text actor.
The sub-test itself might require tweaking.
The cogl_is_* functions were showing up quite high on profiles due to
iterating through arrays of cogl handles.
This does away with all the handle arrays and implements a simple struct
inheritance scheme. All cogl objects now add a CoglHandleObject _parent;
member to their main structures. The base object includes 2 members a.t.m; a
ref_count, and a klass pointer. The klass in turn gives you a type and
virtual function for freeing objects of that type.
Each handle type has a _cogl_##handle_type##_get_type () function
automatically defined which returns a GQuark of the handle type, so now
implementing the cogl_is_* funcs is just a case of comparing with
obj->klass->type.
Another outcome of the re-work is that cogl_handle_{ref,unref} are also much
more efficient, and no longer need extending for each handle type added to
cogl. The cogl_##handle_type##_{ref,unref} functions are now deprecated and
are no longer used internally to Clutter or Cogl. Potentially we can remove
them completely before 1.0.
The test now explicitly reads back from the framebuffer to sanity check that
texturing is happening as expected, and it now uses a fixed 2x2 texture instead
of redhand.png since redhand.png doesn't have a power of two size which can
cause the vertex buffer code to complain on hardware not supporting npot
textures.
The TEST_CONFORM_TODO macro is a simple placeholder macro that
adds the test function to the "/todo" namespace and skips the
test.
It can be used for tests that are known to fail because of bugs
that haven't been fixed yet, or because of features not yet
implemented.
test-vertex-buffer-configuous now needs redhand.png so it should be
copied in to the build directory. This is copied from similar code in
the tests/interactive Makefile.
ClutterModel has an interactive test but lacks a conformance
unit for automatic testing.
This is the beginning of that unit, which covers the population
and iteration over a ListModel.
Sometimes a test unit should not be executed depending on a
condition. It would be good to have a macro doing this, along
with TEST_CONFORM_SIMPLE().
Additionally, the skipped unit should be added to a specific
namespace, so that any coverage report will be able to catch it.
For this reason, here's TEST_CONFORM_SKIP() which follows the
syntax:
TEST_CONFORM_SKIP (condition, namespace, function);
If condition evaluates to FALSE the test is skipped and the
unit added to the "/skipped" namespace.
Fixes some blending issues when using color arrays since we were
conflicting with the cogl_enable state + fixes a texture layer
validation bug.
Adds a basic textured triangle to test-vertex-buffer-contiguous.
The test simply creates an odd sized texture with different colors at
each of the four corners. It then renders the texture and verifies
that the colors are the expected values. This should help ensure that
the sliced texture rendering code is working properly.
The :alignment property is prone to generate confusion: developers
will set it thinking that the contents of a ClutterText will
automagically align themselves.
Instead of using the generic term :alignment, and following the
GTK+ convention, we should use a more specific term, conveying the
actual effect of the property: alignment of the lines with respect
to each other, and not to the overall allocated area.
See bug 1428:
http://bugzilla.openedhand.com/show_bug.cgi?id=1428
This makes it consistent with cogl_rectangle_with_{multi,}texture_coords.
Notably the reason cogl_rectangle_with_{multi,}texture_coords wasn't changed
instead is that the former approach lets you describe back facing rectangles.
(though technically you could pass negative width/height values to achieve
this; it doesn't seem as neat.)
Bug 1349 - Using the anchor point to set the scale center is messy
The branch adds an extra center point for scaling which can be used
for example to set a scale about the center without affecting the
position of the actor.
The scale center can be specified as a unit offset from the origin or
as a gravity. If specified as a gravity it will be stored as a
fraction of the actor's size so that the position will track when the
actor changes size.
The anchor point and rotation centers have been modified so they can
be set with a gravity in the same way. However, only the Z rotation
exposes a property to set using a gravity because the other two
require a Z coordinate which doesn't make sense to interpret as a
fraction of the actor's width or height.
Conflicts:
clutter/clutter-actor.c
During the upgrade to cogl material, test-backface-culling was
switched to use cogl_rectangle instead of cogl_texture_rectangle to
draw the textures. However, cogl_rectangle takes a width and height
instead of the the top-left and bottom-right vertices so the
rectangles were being drawn in the wrong place.
Conflicts:
clutter/cogl/gl/cogl-texture.c
clutter/cogl/gles/cogl-primitives.c
* cogl-material:
clutter-{clone-,}texture weren't updating their material opacity.
Updates GLES1 support for CoglMaterial
Normalizes gl vs gles code in preperation for synching material changes
Removes cogl_blend_func and cogl_alpha_func
Fully integrates CoglMaterial throughout the rest of Cogl
[cogl-material] Restore the GL_TEXTURE_ENV_MODE after material_rectangle
[cogl-material] Make the user_tex_coords parameter of _rectangle const
[test-cogl-material] Remove return value from material_rectangle_paint
Add cogl-material.h and cogl-matrix.h to libclutterinclude_HEADERS
[cogl-material] improvements for cogl_material_rectangle
[cogl-material] Adds a cogl_material_set_color function
[cogl-material] Some improvements for how we sync CoglMaterial state with OpenGL
[cogl-material] Converts clutter-texture/clutter-clone-texture to the material API
[doc] Hooks up cogl-material reference documentation
Updates previous GLES multi-texturing code to use CoglMaterial
Adds a CoglMaterial abstraction, which includes support for multi-texturing
[doc] Hooks up cogl-matrix reference documentation
Adds CoglMatrix utility code
[tests] Adds an interactive unit test for multi-texturing
[multi-texturing] This adds a new cogl_multi_texture API for GL,GLES1 + GLES2
This glues CoglMaterial in as the fundamental way that Cogl describes how to
fill in geometry.
It adds cogl_set_source (), which is used to set the material which will be
used by all subsequent drawing functions
It adds cogl_set_source_texture as a convenience for setting up a default
material with a single texture layer, and cogl_set_source_color is now also
a convenience for setting up a material with a solid fill.
"drawing functions" include, cogl_rectangle, cogl_texture_rectangle,
cogl_texture_multiple_rectangles, cogl_texture_polygon (though the
cogl_texture_* funcs have been renamed; see below for details),
cogl_path_fill/stroke and cogl_vertex_buffer_draw*.
cogl_texture_rectangle, cogl_texture_multiple_rectangles and
cogl_texture_polygon no longer take a texture handle; instead the current
source material is referenced. The functions have also been renamed to:
cogl_rectangle_with_texture_coords, cogl_rectangles_with_texture_coords
and cogl_polygon respectivly.
Most code that previously did:
cogl_texture_rectangle (tex_handle, x, y,...);
needs to be changed to now do:
cogl_set_source_texture (tex_handle);
cogl_rectangle_with_texture_coords (x, y,....);
In the less likely case where you were blending your source texture with a color
like:
cogl_set_source_color4ub (r,g,b,a); /* where r,g,b,a isn't just white */
cogl_texture_rectangle (tex_handle, x, y,...);
you will need your own material to do that:
mat = cogl_material_new ();
cogl_material_set_color4ub (r,g,b,a);
cogl_material_set_layer (mat, 0, tex_handle));
cogl_set_source_material (mat);
Code that uses the texture coordinates, 0, 0, 1, 1 don't need to use
cog_rectangle_with_texure_coords since these are the coordinates that
cogl_rectangle will use.
For cogl_texture_polygon; as well as dropping the texture handle, the
n_vertices and vertices arguments were transposed for consistency. So
code previously written as:
cogl_texture_polygon (tex_handle, 3, verts, TRUE);
need to be written as:
cogl_set_source_texture (tex_handle);
cogl_polygon (verts, 3, TRUE);
All of the unit tests have been updated to now use the material API and
test-cogl-material has been renamed to test-cogl-multitexture since any
textured quad is now technically a test of CoglMaterial but this test
specifically creates a material with multiple texture layers.
Note: The GLES backend has not been updated yet; that will be done in a
following commit.
The rotation centers are now tested in a similar way to the anchor
point and scale centers.
The notification handling code has been simplified a bit to handle the
increased amount of properties.
Since we override the clean-generic target in order to remove
the shell scripts we create for each conformance test unit, we
cannot use CLEANFILES to remove the test reports.
The maintainer compiler flags we use trigger warnings and errors
in the autogenerated code that gtk-doc creates to scan the header
and source files. Since we cannot control that, and we must run
a distcheck with both --enable-gtk-doc and --enable-maintainer-flags
turned on, we need to use less-strict compiler flags when inside
the doc/reference subdirectories.
The way to do this is to split the maintainer compiler flags into
their own Makefile variable, called MAINTAINER_CFLAGS. The we
can use $(MAINTAINER_CFLAGS) in the INCLUDES or _CFLAGS sections
of each part of the source directories we wish to check with the
anal retentiveness suited for maintainers.
This better reflects the fact that the api manages sets of vertex attributes,
and the attributes really have no implied form. It is only when you use the
attributes to draw that they become mesh like; when you specify how they should
be interpreted, e.g. as triangle lists or fans etc. This rename frees up the
term "mesh", which can later be applied to a concept slightly more fitting.
E.g. at some point it would be nice to have a higher level abstraction that
sits on top of cogl vertex buffers that adds the concept of faces. (Somthing
like Blender's mesh objects.) There have also been some discussions over
particle engines, and these can be defined in terms of emitter faces; so some
other kind of mesh abstraction might be usefull here.
To deal with all the corner cases that couldn't be scripted a number of patches
were written for the remaining 10% of the effort.
Note: again no API changes were made in Clutter, only in Cogl.
This is the result of running a number of sed and perl scripts over the code to
do 90% of the work in converting from 16.16 fixed to single precision floating
point.
Note: A pristine cogl-fixed.c has been maintained as a standalone utility API
so that applications may still take advantage of fixed point if they
desire for certain optimisations where lower precision may be acceptable.
Note: no API changes were made in Clutter, only in Cogl.
Overview of changes:
- Within clutter/* all usage of the COGL_FIXED_ macros have been changed to use
the CLUTTER_FIXED_ macros.
- Within cogl/* all usage of the COGL_FIXED_ macros have been completly stripped
and expanded into code that works with single precision floats instead.
- Uses of cogl_fixed_* have been replaced with single precision math.h
alternatives.
- Uses of COGL_ANGLE_* and cogl_angle_* have been replaced so we use a float for
angles and math.h replacements.
Merge branch 'text-actor'
* text-actor: (108 commits)
Re-align ClutterText header file
[text] Fix cursor sizing
Comments and whitespace fixes to ClutterText
[docs] Add newly added :single-line-mode accessors
Update the ignore file
[tests] Add text field interactive test
[text] Add single-line-mode to ClutterText
[text] Fix the deletion actions
[text] Use cached length when possible
[tests] Add unit for the ClutterText:password-char property
[docs] Update the Text section
[text] Coalesce text visibility and password character
Allow localizations to change the text direction
Clean up the update_pango_context() function
Pass the PangoContext, not the MainContext
Revert the logic of the PangoContext check
Remove the binding pool entry from the list
Remove BindingPool::list_actions()
Add ClutterActor::create_pango_context()
Rename the PangoContext creation functions
...
Check that the contents of the Text actor are unaffected by the
:password-char property; that the accessors are correct; and finally
that the initial value for a newly constructed Text actor is valid.
This follows the convention of GtkLabel/GtkEntry in GTK+ and the old
ClutterEntry.
It makes it easier to use strlen/strcmp etc on the output, since we can
assume that it is always a string.
This commit also updates the test unit for ClutterText to verify that
the clutter_text_get_text() function also returns an empty string when
a ClutterText actor has been created.
When building out of tree the generated scripts for the unit tests
need to explicitly reference the original src dir to be able to find
test-launcher.sh, like this:
$(top_srcdir)/tests/conform/test-launcher.sh
Also test-launcher.sh now passes -m slow --verbose to gtester. Without
-m slow then the wrappers dont work for some of the timeline tests.
* cairo-texture:
[cairo-texture] Remove the construct only restriction on surface size
[cairo-texture] Silently discard 0x0 surfaces
Re-indent ClutterPath header
Add a test case for the new cairo path functions
Add clutter_path_to_cairo_path and clutter_path_add_cairo_path
Warn instead of returning in the IN_PAINT check
Small documentation fixes
Print a warning when creating a cairo_t while painting
Do not set the IN_PAINT flag inside the Stage paint
Set the IN_PAINT private flag
[docs] Add ClutterCairoTexture to the API reference
Add ClutterCairoTexture
Require Cairo as a Clutter dependency
Conflicts:
Fix merge conflict in clutter/clutter-path.h
Currently, the conformance test suite creates symbolic links pointing
to a wrapper script that just parses the name used to invoke it and
calls the gtester with the correct path.
Unfortunately, this presents two issues:
- it does not really work on file systems that do not
support symbolic links
- it leaves behind the symbolic links, which cannot
be automatically cleaning by 'make clean'
Both can be solved by creating a small script that invokes the wrapper
one with the test unit path.
The Makefile will use test-conform to extract the unit test paths
and generate a list that will be iterated over to create the
executable name (using the "test-name" convention also used by the
interactive tests, instead of "test_name"); the executable is then
just a simple shell script that invokes the wrapper script passing
the unit test path on the command line. The wrapper script will
use the first argument to work correctly, so it could be simply
executed like:
./test-wrapper.sh /path/to/unit_test
Which is another improvement over the current implementation, where
the wrapper script does not work when invoked directly.
The gdouble value represents an interval along the path from 0.0 to
1.0. This makes more sense than using an alpha value because paths are
not directly related to ClutterAlphas and the rest of the Clutter API
tends to expose gdouble arguments.
The GTest report output allows the developer to know where exactly
a test unit failure happened. The test-text-cache unit makes it
very hard to pinpoint the exact failure location because it relies
on the output to be printed out - which is not the case when the
tests are run as part of a make check.
This commit makes each sub-test inside the unit fail exactly where
the check function fails, which makes it easier to know which sub-test
did actually fail.
The nodes of the test path have been reordered because Cairo coalesces
multiple move operations into a single move so the comparison would
fail if the two move nodes are consecutive.
ClutterText behaviour with regards to the paint opacity has been
changed by commit 07e19fff5ffa9617413fa6c3715914513fec3793.
We need to update the test suite for the paint opacity to reflect
that change as well.
The clutter_text_get_chars() function returns a section of the
contents of the Text actor, delimited by a start and an end position.
This commit adds the implementation for that function and a test
unit that guarantees the offset-to-bytes computations are correct.
Comment why we need to enable the editability of the Text actor
inside the test suite.
This should clarify commit ea508ea528d61ae478d8bc4c88f54a89304f18e8
Whenever we are sending specially crafted KeyEvents to a ClutterText
we also need to set it editable, since the event handling code depends
on the editability setting.
Instead of changing the unit for ClutterEntry, we add a new
test unit specifically for ClutterText so that we can later tweak
it specifically for the behaviour changes needed to make ClutterText
work better.
* clutter/Makefile.am:
* clutter/clutter.h: Add ClutterBindingPool to the build.
* clutter/clutter-binding-pool.c:
* clutter/clutter-binding-pool.h: Add ClutterBindingPool, a data
structure meant to hold (key symbol, modifiers) pairs and associate
them to a closure. The ClutterBindingPool can be used to install
key bindings for actors and then execute closures inside the
key-press-event signal handlers, removing the need for big
switch() or if() blocks for each key.
* clutter/clutter-event.c: Consistently use "key symbol" instead
of "key value".
* clutter/clutter-event.h: Add more modifier masks.
* clutter/clutter-marshal.list:
* tests/conform/Makefile.am:
* tests/conform/test-binding-pool.c:
* tests/conform/test-conform-main.c: Add ClutterBindingPool
conformance test.
* tests/interactive/Makefile.am:
* tests/interactive/test-binding-pool.c: Add interactive test (and
example code) for the ClutterBindingPool usage.
* clutter/clutter-path.h:
* clutter/clutter-path.c: Implementation of new ClutterPath object
to represent a path combining straight line and bezier curve
elements.
* clutter/clutter.h: Include clutter-path.h and remove
clutter-behaviour-bspline.h
* tests/interactive/test-threads.c (test_threads_main):
* tests/interactive/test-script.c:
* tests/interactive/test-behave.c (test_behave_main): Use new path
API
* clutter/clutter-effect.c: Use the new ClutterBehaviourPath API.
* clutter/clutter-bezier.h:
* clutter/clutter-bezier.c: Moved bezier curve handling code out
from clutter-behaviour-bspline.c to a separate file.
* clutter/clutter-behaviour-path.h:
* clutter/clutter-behaviour-path.c: Reimplemented to work with a
ClutterPath
* clutter/clutter-behaviour-bspline.h:
* clutter/clutter-behaviour-bspline.c: Removed
* clutter/Makefile.am: Add clutter-path and clutter-bezier, remove
clutter-behaviour-bspline.
* tests/conform/test-path.c: New automatic test for ClutterPath
consistency
* tests/conform/test-conform-main.c (main): Add test_path
* tests/conform/Makefile.am (test_conformance_SOURCES): Add
test-path.c
* clutter/clutter-sections.txt: Add ClutterPath docs
* clutter/clutter.types:
* clutter/clutter-docs.xml:
* doc/reference/clutter/clutter-animation-tutorial.xml: Remove
mention of ClutterBehaviourBspline
* clutter/clutter-marshal.list: Add VOID:UINT
* tests/conform/test-mesh-interleved.c:
* tests/conform/test-mesh-contiguous.c: Remove the idle source
after the test is complete so that it won't interfere with other
tests.
* tests/tools/Makefile.am: Optionally build the
libdisable-npots.la library depending on whether libdl was
detected in the configure script. A helper script is also
generated to setup the LD_PRELOAD.
* tests/conform/Makefile.am: There are now two versions of the
test-report and full-report rules. test-report-normal is the same
as before and test-report-disable-npots runs the tests with the
disable-npots wrapper script. The full-report rule runs both of
them and displays two separate HTML files. The test-report rule
just runs the normal version as before.
* configure.ac: Add a test for libdl
* tests/tools/disable-npots.sh.in: New file. Template for the
helper script
* tests/tools/disable-npots.c: New file
* tests/conform/test-conform-main.c (main): Do not run the
conformance test suite if we are on X11 but we do not have
a DISPLAY available. Some of the tests require a DISPLAY,
and everything passes through a clutter_init() call which will
fail anyway. If we are running make distcheck on an headless
box we might as well just skip the conformance test suite
without a meaningless error.
* tests/conform/test-mesh-contiguous.c:
* tests/conform/test-mesh-interleved.c:
* tests/conform/test-mesh-mutability.c: Remove the last bare
g_print() from the conformance test suite.
* clutter/cogl/common/cogl-mesh.c:
Make sure we use the appropriate cogl_wrap_gl* funcs as appropriate
* clutter/cogl/gles/cogl-gles2-wrapper.c
* clutter/cogl/gles/cogl-gles2-wrapper.h:
In our glColorPointer wrapper we needed to mark our color attribute
as normalized.
* tests/conform/Makefile.am:
When creating unit test symlinks we use the -l gtester option to
list tests, but when using the PVR SDK the test binary also spews
out some extra info that caused lots of random symlinks to be
created. We now grep for lines starting with a '/'
* tests/conform/test-mesh-contiguous.c
* tests/conform/test-mesh-mutability.c:
Use cogl_set_source_color instead of directly calling glColor4ub
* tests/conform/Makefile.am:
* tests/conform/test-conform-main.c:
* tests/conform/test-paint-opacity.c: Add test unit for label,
rectangle and paint opacity.
* tests/conform/test-mesh-mutability.c (on_paint):
* tests/conform/test-mesh-interleved.c (on_paint):
* tests/conform/test-mesh-contiguous.c (on_paint): Use g_usleep
instead of sleep
* tests/conform/test-mesh-mutability.c (queue_redraw):
* tests/conform/test-mesh-interleved.c (queue_redraw):
* tests/conform/test-mesh-contiguous.c (queue_redraw): Added
missing return statement
* clutter/cogl/cogl-mesh.h: Add a declaration for
cogl_mesh_submit
* clutter/cogl/common/cogl-mesh.c (cogl_mesh_submit): Move the
documentation to cogl-mesh.h to match the rest of the functions
* clutter/cogl/cogl-mesh.h
* clutter/cogl/cogl-types.h
* clutter/cogl/cogl.h.in
* clutter/cogl/common/Makefile.am
* clutter/cogl/common/cogl-mesh-private.h
* clutter/cogl/common/cogl-mesh.c
* clutter/cogl/gl/cogl-context.c
* clutter/cogl/gl/cogl-context.h
* clutter/cogl/gl/cogl-defines.h.in
* clutter/cogl/gl/cogl.c
* clutter/cogl/gles/cogl-context.c
* clutter/cogl/gles/cogl-context.h
* doc/reference/cogl/cogl-docs.sgml
* doc/reference/cogl/cogl-sections.txt:
The Mesh API provides a means for submitting an extensible number of
per vertex attributes to OpenGL in a way that doesn't require format
conversions and so that the data can be mapped into the GPU (in vertex
buffer objects) for - hopefully - fast re-use.
There are a number of things we can potentially use this API for, but
right now this just provides a foundation to build on. Please read
the extensive list of TODO items in cogl-mesh.c for examples.
Please refer to the cogl-mesh section in the reference manual for
documentation of the API.
* tests/conform/Makefile.am
* tests/conform/test-conform-main.c
* tests/conform/test-mesh-contiguous.c
* tests/conform/test-mesh-interleved.c
* tests/conform/test-mesh-mutability.c:
Privides basic coverage testing for the mesh API.
* tests/conform/test-conform-common.c
* tests/conform/test-pick.c:
Instead of using clutter_stage_new /clutter_actor_destroy as a way to
avoid cascading side effects between unit tests, due to left over
actors, we now destroy all children of the default stage between
tests instead.
* tests/conform/wrapper.sh:
Adds a convenience note about how to run valgrind for an individual
unit test
* tests/conform/test-label-cache.c:
* tests/conform/test-pick.c:
* tests/conform/test-timeline.c: Show all the output messages only
if the test was done with the verbose flag turned on.
* tests/interactive/test-main.c: Do not use the (gpointer*) cast,
but use a temporary gpointer instead.
* tests/conform/wrapper.sh:
* tests/conform/test-conform-main.c:
* tests/conform/test-timeline.c:
Adds Neil's updates to test-timeline.c so it now works with the new unit
testing infrastructure.
Also some fixes to ensure wrappers get setup correctly for the timeline
tests.
* tests/interactive/test-main.c:
cast the symbol return pointer as (gpointer *) to avoid warning
* tests/conform/test-pick.c:
g_assert that the test passes, instead of using exit()
* test/conform/ADDING_NEW_TESTS:
Fixes a silly typo
* tests/conform/Makefile.am:
* tests/conform/test-actor-invariants.c:
* tests/conform/test-conform-main.c: Move the actor invariants
unit to the conform section of the test suite.
* tests/interactive/Makefile.am:
* tests/interactive/test-entry-auto.c:
* tests/interactive/test-invariants.c: Remove the entry-auto
and invariants test, since those two belong to the conform
section.
framework
* configure.ac:
* tests/*:
The tests have been reorganised into different categories: conformance,
interactive and micro benchmarks.
- conformance tests can be run as part of automated tests
- interactive tests are basically all the existing tests
- micro benchmarks focus on a single performance metric
I converted the timeline tests to conformance tests and also added some
tests from Neil Roberts and Ebassi.
Note: currently only the conformance tests use the glib test APIs,
though the micro benchmarks should too.
The other change is to make the unit tests link into monolithic binaries
which makes the build time for unit tests considerably faster. To deal
with the extra complexity this adds to debugging individual tests I
have added some sugar to the makefiles so all the tests can be run
directly via a symlink and when an individual test is run this way,
then a note is printed to the terminal explaining exactly how that test
may be debugged using GDB.
There is a convenience make rule: 'make test-report', that will run all
the conformance tests and hopefully even open the results in your web
browser. It skips some of the slower timeline tests, but you can run
those using 'make full-report'
